ATSU01N222LT
ATS01U 22ASoft strt/stop 200-480V
Trade Price
POA
Per
1
Unit
EA
Pack Quantity
1
Information
The Altistart U01 is a soft start/soft stop unit for 3-phase asynchronous motors. It is designed primarily for combinations with TeSys U starter-controllers. It can be used for a motor rated power up to 11kW or 15hp for 3-phase (200V to 480V AC) and up to 22A rating. It is 45mm wide, this makes it one of the smallest soft starters on the market. It can be installed nearly everywhere. It features an Integrated bypass, this reduces noise and decreases heat dissipation. Its protection index is IP20. It weighs 0.49kg and its dimensions are, 45mm wide, 314mm high, 170mm deep. The Altistart U01 is designed for the following simple applications like conveyors, conveyor belts, pumps, fans, compressors, automatic doors and gates, small cranes and belt-driven machinery. It complies with standards IEC/EN 60947-4-2, and carries UL, CSA, C-Tick, and CCC certifications, and CE marking. It can be easily combined with a TeSys U controller by means of the power connector VW3G4104. It is easy to install on a DIN rail. Altistart 01 combines simplicity with easy cabling, fast configuration and efficiency. Reduced machine wear and minimized maintenance time will optimize operations. Together with TeSys Model U, it provides a unique motor starter solution.
Technical Specifications
Range of product
Altistart U01 and TeSys U
Product or component type
Soft starter
Product destination
Asynchronous motors
Product specific application
Simple machine
Device short name
ATSU01
Network number of phases
3 phases
[Us] rated supply voltage
200...480 V - 10...10 %
Motor power kW
11 kW, 3 phases at 400 V 4 kW, 3 phases at 230 V 7.5 kW, 3 phases at 400 V 5.5 kW, 3 phases at 230 V
Motor power hp
5 hp, 3 phases at 230 V 7.5 hp, 3 phases at 230 V 10 hp, 3 phases at 460 V 15 hp, 3 phases at 460 V
IcL starter rating
22 A
Utilisation category
AC-53B conforming to EN/IEC 60947-4-2
Current consumption
100 mA
Type of start
Start with voltage ramp
Power dissipation in W
2.5 W at full load and at end of starting 222.5 W in transient state
Assembly style
With heat sink
Function available
Integrated bypass
Supply voltage limits
180…528 V
Supply frequency
50...60 Hz - 5...5 %
Network frequency
47.5...63 Hz
Output voltage
<= power supply voltage
[Uc] control circuit voltage
24 V DC +/- 10 %
Starting time
1 s / 100 5 s / 20 10 s / 10 Adjustable from 1 to 10 s
Deceleration time symb
Adjustable from 1 to 10 s
Starting torque
30...80 % of starting torque of motor connected directly on the line supply
Discrete input type
Logic (LI1, LI2, BOOST) stop, run and boost on start-up functions <= 8 mA 27 kOhm
Discrete input voltage
24...40 V
Input output isolation
Galvanic between power and control
Discrete input logic
Positive LI1, LI2, BOOST at State 0: < 5 V and <= 0.2 mA at State 1: > 13 V, >= 0.5 mA
Discrete output current
2 A DC-13 3 A AC-15
Discrete output type
Open collector logic LO1 end of starting signal Relay outputs R1A, R1C NO
Discrete output voltage
24 V (voltage limits: 6...30 V) open collector logic
Minimum switching current
10 mA at 6 V DC for relay outputs
Maximum switching current
Relay outputs: 2 A at 30 V DC cos phi = 0.5 and L/R = 20 ms inductive load Relay outputs: 2 A at 250 V AC AC-15 cos phi = 0.5 and L/R = 20 ms inductive load
Maximum switching voltage
440 V relay outputs
Display type
1 LED (green) for starter powered up 1 LED (yellow) for nominal voltage reached
tightening torque
1.9…2.5 N.m 0.5 N.m
Electrical connection
4 mm screw clamp terminal - rigid 1 1...10 mm² AWG 8 power circuit Screw connector - rigid 1 0.5...2.5 mm² AWG 14 control circuit 4 mm screw clamp terminal - rigid 2 1...6 mm² AWG 10 power circuit Screw connector - rigid 2 0.5...1 mm² AWG 17 control circuit Screw connector - flexible with cable end 1 0.5...1.5 mm² AWG 16 control circuit 4 mm screw clamp terminal - flexible without cable end 1 1.5...10 mm² AWG 8 power circuit Screw conn
Document Links
Datasheet
Brochure